ZorantaGuides
Tankleaf

Tankleaf › Guides

High Nitrates in Aquarium Water: Causes and What to Do

Nitrate is the end product of the nitrogen cycle, so every stocked aquarium produces it. A high reading means more is being made than your water changes and plants remove. The fix is to bring it down gradually with partial water changes, then deal with the cause: usually feeding, stocking, gaps between water changes, or nitrate already in the tap water.

What counts as "high" depends on what you keep. Check the range for your species with the breeder, a species guide or your shop, and use that as your target.

A densely planted aquarium with light falling through the water

High nitrates in aquarium water: first steps

  1. Retest. Shake the nitrate reagent bottles hard as the kit instructions say; a poorly mixed bottle can read low or high. Read the colour in daylight.
  2. Make sure it is nitrate, not nitrite. NO₃ (nitrate) and NO₂ (nitrite) look alike on a test card. Nitrite is the more urgent of the two.
  3. Test your tap water with the same kit. If it reads high too, water changes alone cannot bring the tank below it.
  4. Watch the animals. Lethargy, gasping or loss of colour can point to several problems, not only nitrate.
  5. Start with a moderate water change, then repeat over the following days rather than changing most of the water at once.

Large, sudden swings in water chemistry can stress fish and invertebrates, especially in a tank whose water has drifted a long way from the tap water over months. Several smaller changes are gentler than one very large one.

Tankleaf

Tankleaf shades your target range on each chart and marks water change days, so you can see whether nitrate drops after each change and where it climbs back to. Get it on Google Play

Why nitrate builds up

CauseHow to tellWhat helps
OverfeedingFood left on the substrate; cloudy waterFeed less; remove leftovers
Too many or too large fish for the tankNitrate climbs fast even with weekly changesLarger or more frequent changes; reconsider stocking
Long gaps between water changesReadings rise steadily between changesA regular schedule
Topping up instead of changing waterWater level kept full but no water removedReplace topping up with partial changes
Dirty substrate or filterMulm when you stir the gravel; slow filter flowGravel vacuum; rinse media in tank water
Dead or decaying matterA missing fish, melting plants, rotting foodFind and remove it
Nitrate in tap waterTap water test reads above zeroSee the tap water section below

How to lower nitrates in an aquarium

Water changes

This is the quickest and most direct method. A 25% change removes roughly a quarter of the nitrate, as long as the new water has less. Repeat every few days until the reading reaches your target, then set a weekly size that keeps it there. Our guide on how often to change aquarium water shows the math.

Feed less

Less food in means less waste out. Feed amounts the fish finish quickly and skip a day now and then if your species tolerate it.

Clean the substrate

Waste settles in gravel and sand. Vacuuming a section at each water change removes it before it breaks down.

Add plants

Fast-growing stem plants and floating plants take up nitrate as they grow. They only help while they are growing, so remove melting leaves.

Nitrate-removing media

Some filter media and resins remove nitrate. They treat the symptom rather than the cause, need replacing or recharging, and work alongside water changes rather than instead of them. Follow the maker's instructions.

High nitrates in aquarium after a water change

If nitrate barely moves after a change, the most common explanation is the tap water. Test it on its own. In the United States your supplier publishes nitrate results in its annual Consumer Confidence Report; in England and Wales the Drinking Water Inspectorate explains how to find your supplier's data. Drinking water limits are set for people, not for aquarium animals.

If the tap reads high, options include mixing in water treated by reverse osmosis (re-mineralised to suit your fish), more plants, or nitrate-removing media. Other reasons a change seems not to work: the change was small, the test reagents need shaking, or something is decaying in the tank.

High nitrates in aquarium without fish

During a fishless cycle, rising nitrate is the sign the cycle is working: the bacteria are turning ammonia and nitrite into nitrate. A large water change at the end of the cycle brings it down before fish go in. Outside a cycle, an empty tank with rising nitrate usually has decaying food, plant matter or tap water nitrate behind it.

Keeping nitrate steady

This is general information, not husbandry or veterinary advice. Safe levels vary by species. Follow your test kit's instructions, and ask a vet who treats fish if animals show signs of illness.
Tankleaf

Spot the rise before it gets high

Log nitrate with your other tests in Tankleaf; values outside your target range are marked in amber on the home screen.

Get it on Google Play

iPhone version coming soon

More guides

All guides

Sources

Published by Zoranta, the developer of Tankleaf.