ZorantaGuides
Candle Shelf

Candle Shelf › Guides

Candle Tunneling: Why It Happens and How to Fix It

Candle tunneling is when the flame burns a narrow hole down the middle of the candle and leaves a thick wall of unmelted wax around the edge. It usually starts with a first burn that ends before the melted wax reaches the sides of the jar. Each later burn then follows the same small circle.

A shallow tunnel can often be fixed by melting the wax at the edges until the surface is level again, using a foil collar or gentle heat from above. A deep tunnel with a drowned or very short wick may not be worth saving. The sections below cover the causes, the fixes and the habits that help prevent it.

A lit jar candle with an even melt pool and a wick trimmer beside it

What candle tunneling is and why it happens

Wax in a container candle tends to melt to the same width it reached the last time it burned. Candle makers call this the memory ring. If the first burn only melts a small pool around the wick, that small pool becomes the pattern, and the flame keeps sinking into it.

Common causes:

Is it the candle or the way it was burned?

If a candle tunnels even after a long first burn in a still room, the wick may simply be too small for the jar. That is a product issue rather than a burning habit, and the maker or the shop is the right place to ask. If the candle burned evenly at first and only tunneled after a few short sessions, the burn length is the more likely cause.

Candle Shelf

Candle Shelf lets you log each burn with how long it lasted and how the throw was, so you can look back at how a candle behaved before you buy that scent again. Get it on Google Play

Candle tunneling fix: three methods

Before you try any of these, read the warning label on your candle and follow the maker's instructions where they differ. Keep the candle on a heat-resistant surface, away from anything that can catch fire, and stay in the room while it burns.

1. The foil trick

The candle tunneling foil trick uses a collar of aluminum foil to hold heat over the outer wax.

  1. Trim the wick, then light the candle.
  2. Wrap a strip of foil around the top of the jar so it folds in over the wall of wax and leaves an opening of an inch or two in the middle over the flame.
  3. Let it burn and check it often. The foil reflects heat onto the stuck wax at the edges.
  4. When the surface has melted level from edge to edge, remove the foil with an oven glove or tongs, as it gets hot, and let the candle keep burning normally or blow it out.

Keep the opening wide enough that the flame has air and does not touch the foil. If the flame becomes large, smoky or flickers hard, put it out and let the candle cool before trying again.

2. Level the wax with gentle heat

With the candle unlit, some people warm the top of the wax with a hair dryer until the outer ring softens and slumps toward the middle. This works for shallow tunnels. It can push melted wax over the rim, so keep the dryer moving and hold it a little way off. Another option is a candle warmer lamp, which melts the top layer from above without a flame.

3. Scoop out some of the wall

For a deep tunnel, you can carefully scrape away part of the unmelted wall with a spoon while the candle is cool, so the flame is no longer sitting at the bottom of a well. Save the scraped wax for a wax warmer if you have one.

These are general tips, not safety instructions for your specific candle. Follow the warning label and the maker's guidance, and see the NFPA's candle safety tips for the basics of burning candles at home.

When a tunneled candle is not worth saving

In those cases, many people move the remaining wax to a wax warmer instead. If the candle tunneled from the very first burn, contacting the maker is also reasonable.

How to prevent candle tunneling on the first burn

The first burn sets the pattern, so it is worth planning for. A common rule of thumb from candle makers is to let the candle burn until the melt pool reaches the edge of the jar, which takes about an hour for every inch of the candle's width. A 3-inch jar might need around three hours. That is a guide, not a fixed figure, so watch the wax rather than the clock.

Jar width (example)Rough first-burn time by the 1 hour per inch rule
2 inchesAbout 2 hours
3 inchesAbout 3 hours
4 inchesAbout 4 hours

Many candles also print a maximum burn time on the label, and a wide jar can reach that limit before it melts fully. If the two conflict, follow the label, let the candle cool, and continue the next time.

Habits that help after the first burn

Burn length also decides how many hours a jar lasts. Our guide to candle burn time shows how to work that out for your own candles.

Candle Shelf

Remember which candles burned well

Candle Shelf keeps your collection on your phone, with a log of each burn and a rating for each scent, so a candle that tunneled every time is easy to spot next time you shop.

Get it on Google Play

iPhone version coming soon

More guides

All guides

Sources

Published by Zoranta, the developer of Candle Shelf.